Quanzhou Sanqi Engineering Machinery Co.Ltd

enLanguage
KX161-3 Excavator Bottom Roller

KX161-3 Excavator Bottom Roller

Color:black,yellow,blue,gray
Mini track roller type:inner flange,outter flange
Bushing type:bearig,bimetabl bushing
mounting type:shaft bolt type,collar type

Product Introduction

KX161-3 excavator bottom roller

Production Description

An excavator bottom roller is one of the essential components of an excavator machine, and it plays a crucial role in helping the machine move and operate effectively. A high-quality excavator track roller must possess several essential conditions to ensure that it works efficiently and effectively.

 

Structure of KX161-3 excavator bottom roller

 

image

 

Sizes of KX161-3 excavator bottom roller

 

image

 

Advantages of KX161-3 excavator bottom roller

 

1. Each roller shell is carefully heat treated to ensure long wear life and stress resistance.

2. Differential type of quenching or through type of quenching heattreatment can ensure certain heat treatment hardness depth and so give good anti-cracking effects.

 

Technical requirement

1. Check all parts strictly before assembly and clean them

2. A small amount of oil shall be applied to the mating surface of the shaft sleeve and straight shaft before assembly

3. The floating oil seal ring shall be assembled in pairs, and its sealing surface shall be coated with lubricating oil. O-ring and floating oil seal ring

The contact surface shall not be coated with grease, and the assembly of floating seal rubber ring shall not be twisted

4. During assembly, pay attention to the oil groove direction of the shaft and the installation plane of the side cover

5. After assembly, ensure that the axial clearance is 0.4-0.7mm. Rotate the wheel body by hand, and feel the resistance moment, but there is no jamming,

6. After installation, fill in the filtered lubricating oil and check that there is no leakage. Then run in for 3-5 minutes to make it run smoothly

7. The painting color shall comply with jb2299-78 or the customer's requirements

track roller painting

 

MODELS AVAILABLE:

KUBOTA:K008/K013/K030/K035/K040/K045/KH14/KH025/KH026/KH101/KH36/KH41/KH51/KH61/KH90/KX018/KX024/KX027/KX033/KX045KX057/KX080/KX101/KX121/KX161/KX36/KX41-2/KX41-3

 

FAQ

1. Hydraulic Cylinder Internal Leakage?

There are 3 main reasons causing internal leakage :Overload,polishing is not well controlled,bad seal kits.As is known to all,vehicles in China are often overload,our products all designed to bear the overload power.We have numerical control machine to assure the polish processing .And we use the imported seals to meet customers' demands.

2. Does Your Piston Rod Get Ruptured Easily?

Hard chrome plating quenched and tempered 45# steel for piston rod to assure sufficient hardness and toughness.

3. Is Your Design Reasonable? What About Your Product Safe Coefficient?

We have R&D team with abundant design experience. We also established production, education, and research cooperation with universities . Rest assured.

4. What About The Quality Feedback Of Your Products?

Guarantee the quality from the raw material. We have cold drawing production line and nickel-chrome electroplating production line , so we can produce cold-drawing pipe and hard-chrome pipe used for hydraulic cylinder. !!! We have never received even once quality complaint for many years of international trade.

5. Is The Sample Free?

Yes.In our acceptable range, we can offer a sample by charging freight. And we will return the fee after you place bulk order.

6. What 'S The After-Service?

If the quality can't meet your requirement ,we will pay all your lost and offer technical support to solve your problem!!!

 

 

Hot Tags: kx161-3 excavator bottom roller, China, best, manufacturers, suppliers, factory, Carrier Roller SH200 SH280 SH210 5, Mini Track Roller PC50UU, Front Idler VIO15, Track Roller SK30, Track Link PC200 5 PC200 6 PC200 7 PC200 8, Front Idler BD2G

You Might Also Like

(0/10)

clearall