
Ym301 Excavator Bottom Roller
Material:50MN
Packing:wooden pallets
guarantee time:6 months under normal usage
Product Introduction
ym301 excavator bottom roller
Production description
excavator bottom roller assembly also called bottom roller assembly or lower roller assembly are often in mud, water and just and bear strong impact. Therefore,they are required to be sealed reliably and wear-resisitant.
We will select different material as per different working condition for our track roller assembly to meet customer requirements and machine precisely and assemble them well to guarantee the hight quality.
Our advantages of lower roller assembly are as below:
State-of-the art machining
Each roller assembly shaft is machined by the utilization of the most modern technological advances known to the industry, Grinding and finishing methods ensure mirror like finish and tempering with medium to low frequency heat treating equipment guarantees maximum strength.
Maximum life
Each bottom roller assembly shell is carefully heat treated to ensure long wear life and stress resistance.
Precision care
Each lower roller assembly is precision machined to house special high impact low wear bimetal bushings.
Oil Leakage Inspection and Elimination
1. In the process of installation, strict inspection shall be carried out according to the technical requirements of the parts, so as to keep them clean and prevent impurities from entering the installation surface. Especially the sealing face of the sealing ring, even if there are small dust particles, it will destroy the sealing and cause oil leakage.
2. Seal sleeve and rubber ring need to be replaced for aging, deformation, scarring and rupture.
3. Spring should be replaced when its elasticity is insufficient. Its end surface is uneven and can be ground flat. When the coil is warping, it should be repaired and trimmed, and the sharp edges should be removed.
4. Large and small sealing rings are not in strict contact and can be re-grinded to make them have uniform and continuous grinding rings. Do not touch the end of the ring and disturb the spouse ring. The thickness of the ring should be the same, otherwise it must be replaced.
5. The thickness of rubber ring is not enough. It is allowed to wrap asbestos rope to achieve a tightness of/0.15-0.20 kg per square centimeter.
6. Bending of axle, non-circular or neck wear, wear of supporting wheel hub and sealing shell matching belt must be repaired.
Models Available For Yanmar Excavators:
VIO15,VIO17,VIO18,VIO20,VIO30-1,VIO30-2,VIO35,VIO40-1,VIO40-2,VIO50-2,VIO50-6,VIO70,VIO75,VIO55-2,VIO55-6,B17,B27,B37,B50 ,YB151,YB201,YM301,YM501ETC..
FAQ
1. You Are A Trader Or A Manufacture?
We Are A Factory Located On Quanzhou Fujian,China.
2. How Can I Be Sure The Part Will Fit My Excavator?
Give Us Correct Model Number/Machine Serial Number/ Any Numbers On The Parts Itself. Or Measure The Parts Give Us Dimension Or Drawing.
3. How About The Payment Terms?
We Usually Accept T/T Or L/C. Other Terms Also Could Be Negotiated.
4. What Is Your Minimum Order?
It Depends On What You Are Buying. Normally, Our Minimum Order Is USD5000. One 20' Full Container And LCL Container (Less Than A Container Load) Can Be Acceptable.
5. What Is Your Delivery Time?
FOB Xiamen Or Any Chinese Port : 35-45 Days . If There Are Any Parts In Stock , Our Delivery Time Is Only7-10 Days.
6. What About Quality Control?
We Have A Perfect QC System For The Perfect Products. A Team Who Will Detect The Product Quality And Specification Piece Carefully, Monitoring Every Production Process Until Packing Is Complete, To Ensure Product Safety Into Container.
Hot Tags: ym301 excavator bottom roller, China, best, manufacturers, suppliers, factory, EX60 Track Roller, Sprocket Rim PC650 PC800, Big Excavator Sprocket, Sprocket Rim SK045N2, Excavator Track Roller Assy, Boom Cylinder Assy
You Might Also Like
Send Inquiry







