Quanzhou Sanqi Engineering Machinery Co.Ltd

enLanguage
Crawler Crane Track Shoe

Crawler Crane Track Shoe

Crawler Crane Track Shoe Production introduction: In normal operation, the track pin slowly rotates backward in the pin hole, and the two wear evenly, the pin hole gradually becomes larger, and the pin gradually becomes thinner. If the operation is improper, such as turning at high speed,...

Product Introduction

Crawler Crane Track Shoe

Production introduction:

Classification of chain plates
Chain plate mainly includes the following types: chip conveyor chain plate, metal chain plate, conveyor chain plate, cleaning chain plate, beer metal chain plate, chip conveyor chain plate, punching chain plate, stainless steel chain plate, carbon steel chain plate, transmission chain plate, engineering plastic chain plate, keel chain plate, etc.
Main features of chain plate: smooth surface operation, and not easy to be interfered by other materials, can bear heavy materials, durable. According to the specific situation, we can design and produce the chain plate of suitable specification. The commonly used chain plate specifications are 31.75, 38.1 and 50.8. Compared with other drive belts, the cost is higher.



In normal operation, the track pin slowly rotates backward in the pin hole, and the two wear evenly, the pin hole gradually becomes larger, and the pin gradually becomes thinner. If the operation is improper, such as turning at high speed, starting abruptly, or entering mud, weeds and so on to block the pin, the pressure on the left and right sides of the track shoe will be too heavy to bend down, the pin will be deformed and bent, and cannot rotate in the pin hole, the pin and the pin hole will become sliding friction, and the friction part is limited to a small part of the contact surface, the pin will gradually grind into a crank shape, and the pin hole will also become an ellipse. The increase of pin hole also causes the lengthening of track pitch (pitch is the center distance of holes at both ends of track shoe), so the track shoe and driving wheel grind each other, the track shoe is worn through, and the teeth of driving wheel are in the shape of blade. According to the measurement, when the pitch changes from 174 mm to 184 mm, the opening width of the driving wheel teeth changes from 87 mm to 97 mm, then the normal rolling engagement is completely destroyed.


Because of the lengthening of the track shoe pitch, it also causes the roller to jump when walking, which accelerates the wear of the track part of the track shoe. When the runway part is sunk more than 4mm, it should be repaired. The wear of the guide part of the track shoe is mainly caused by the track deviation, the serious deformation of the track shoe, and the axial shaking of the roller and the guide wheel. The common scrapped track shoes are severely worn or worn through at the meshing part with the driving wheel


Common faults and maintenance of chain board
During the transportation of chain plate, the operation is often unstable and deviated:
The maintenance method is as follows:
First of all, adjust the tension shaft of the chain plate, with proper tightness, so as to avoid unnecessary damage to the edge.
Secondly, check whether there is corrosion in the chain conveyor and replace it if necessary.

Finally, check whether the two ends of the chain drive shaft are synchronous and whether the tooth end is excessively worn.


Precautions in use of chain plate
First of all, when using the chain plate, avoid direct contact with the heat source, gather at least one meter away, and avoid direct sunlight and other weather factors when using in the open air. And the conveying speed shall be less than 2.5m/s. In the use process, the tension of chain plate should not be too large, and the minimum tension should be kept as far as possible under the premise of ensuring that the chain plate is engaged with the gear and does not bend. And it must be ensured that a chain plate of the same model and material is used in a machine.
When the chain plate is in operation, it should be ensured that the empty machine of the driving machine is in operation. Because the acceleration required for starting is quite large, if there is material on the chain plate when starting, the problem of too high load of gear slip motor may occur. When the machine is stopped, try to ensure that the materials on the chain plate are emptied. When the multi-level chain board is running, the opening sequence should be to open the last level, and then move forward in sequence. The shutdown sequence is the opposite.

crane track shoe

Crawler track shoe,Crawler track shoe plate,Crawler track pad

HitachiKH100/30T,KH100-2/3KH125/35T,KH150/40T,KH180/50T,KH300/80T,KH500/100T,
KH700/150T,KH850/150T,KH1000/200T
KobelcoP&H60P,P&H70P,P&H75P,P&H100P,P&H315,P&H320,P&H325,P&H330,P&H335,
P&H335AS,P&H345,P&H440,P&H550A,P&H550-1,P&H550-2,P&H5035,P&H5045,
P&H5055,P&H5100,P&H7035,P&H7045,P&H7050,P&H7055,
P&H7065,P&H7070,P&H7080,P&H7090,P&H7100,P&H7120,P&H7150,P&H7200,
P&H7250,P&H7250-2,FS80,FS90,BM500,BM600,BM650,BM700,BM700HD,BM750,BM800,
BM800HD,BM900,
BM900HD,BM1200,CKS600,CKE600,CKE700,CKE800,CKE850,CKE900,CKE1000,CKE1100,
CKE1350,CKE1800,CKE2500,CKE2500-2,CKE850,CK1000,CK1000G,CK1600,CK2000-2,
CK2500,SL6000 ETC..
SumitomoSC500-2/50T,SC700/70T,SC2500/250T,LS78R,LS108/40T,LS118-5/50T,LS120,LS218/80T,LS238/100T,LS248/150T,LS368,LS468,SA1700
IHICCH250W,CCH280W,CCH500/50T,DCH700/70T,DCH800/80T,CCH800,CCH1500E,
CCH2500/250T
Minitowoc4100WS1/180-272T,4100S,4600S4/317.5,M250/250T,M2250/272T,M999/250T,M4600/317.5T,M18000/600T,M21000/1000T
DemagCC1400/250T,CC1800/300T,CC2000/300T,CC2200/350T,CC2400/400T,CC2500/450T,
CC2800/600T,CC5800/1000T
SanySCC500,SCC600,SCC750,SCC800,SCC1000,SCC1250,SCC1500,SCC1800,SCC2600,SCC4000,SCC6500,SCC7500,SCC10000,SCC16000
ZoomlionQUY50,QUY70,QUY80,QUY100,QUY130,QUY180,QUY200,QUY260,QUY350,QUY400,QUY450,QUY500,QUY550,QUY600,QUY650,QUY800,QUY1000,ZTM300,ZTM500,ZTM750,ZTM800,ZTM550,ZTM3200

FAQ

1. Are you a manufacturer or a trader?

We are a manufacturer. We do forging and casting by ourselves. And our factory is located in Quanzhou city, Fujina, China.

2. How could you know if our parts are fitted to machines?

Please offer us the detailed machine models or mounting sizes.

3. How about the payment terms?

TT 30 percent deposit,and TT 70percent balance after seeing the scan copy of bill of lading or LC at sight.

4. What is the delivery time?

Generally speaking, the delivery time is 20days to 45days.it depend on how many items for a order. But if the whole order are 200 serial track roller(bottom roller, lower roller), the delivery time is within 10days.


Hot Tags: crawler crane track shoe, China, best, manufacturers, suppliers, factory, Swamp Track Shoe, Rubber Track Shoe Plate, Bulldozer Track Shoe Plate, Excavator Track Shoe, Excavator Track Shoe Plate, Bulldozer Track Shoe

You Might Also Like

(0/10)

clearall