Why did the excavator skip its chain? How to solve derailment easily
Driving the excavator is to earn sweat and blood, but I didn't expect to drop the chain again at the critical moment. Why can't the track often get through with me? Excavator chain drop is usually referred to as derailment, how come the "derailment" happen? How to install the track chain quickly when it's dropped?
Seven reasons to quickly understand why the excavator derailed?
In order to quickly solve the derailment of excavator track, first of all, we should find out the cause of the failure, and then we can quickly prescribe the right medicine. The "chain drop" of excavators is generally caused by the following seven reasons.
Because of the chain drop caused by external reasons, the crawler of the excavator enters the earth or stones and other impurities, through the rugged road will also make the force of the crawler plate seriously unbalanced, which is prone to failure.
The manipulation skill of the operator is not good enough. If the excavator is not properly operated during turning or walking, it will also cause derailment.
Track derailment is caused by the different planes of the four wheels, which is often caused by the damage of the guide wheels. It is necessary to carefully observe whether the screw on the guide wheel is missing, whether there is a break, and whether the groove of the guide wheel is clamped, and whether there is a variant, etc. If necessary, the guide wheel needs to be replaced.
When the oil seal of the tightening cylinder leaks and the spring of the tightening device breaks, it will cause the track to be too loose, which will cause the problem of derailment. Should check whether the tightening cylinder forgot to beat butter in time to see if there is oil leak in the tightening cylinder.
When the chain protector is worn seriously, it will also cause the digger to release the chain. The chain protector can not well limit the caterpillar, and the caterpillar plate swings too much, which will cause the chain to be released.
If the excavator walks too long, the caterpillar must be worn out, and the wear of the caterpillar chain, chain barrel and other parts will also cause the caterpillar to be unchained.
For the drive motor gear ring, when the wear is too serious, it needs to be replaced in time, which will also cause the digger to be out of chains.
The old driver teaches you two ways to quickly solve the problem of digger derailment
First type: bucket installation using excavators
One of the most common ways of installation is to use the excavator's bucket. First of all, they should remove the chain-breaker, release the butter, and let the track relax. Then, according to the situation, they should use the excavator bucket and walking to cooperate, and the track slides out, so that they can first push part of the track onto the guide wheel or driving wheel with the bucket, and then rotate the driving wheel to load the track back.
If the track slides inward, the bucket can't reach the track. This requires a wire rope to pull part of the track onto the guide wheel or the driving wheel, and then rotate the driving wheel. But the operation is to be noted that the excess distance of track relaxation should be more in the installation site, so it is easier to install. After the position of the guide wheel and the driving wheel is installed, the track is basically half installed. The position of the supporting wheel can be installed by lifting the idling track.
The second is to use steel pipe or spade to install caterpillars.
Previously, in the article "Only 5 minutes, 1 steel pipe, quick solution to mini digger derailment ", I also shared with you a method of fast track installation:
Step 1: When the track come off, keep calm and calm, and remember to put grease first.
Step 2: Take local materials at the construction site, find a steel pipe or spade, and remember to find a longer one.
Step 3: Skillfully use the Leverage Principle, pin the steel pipe back with a dug bucket and squeeze out the Yellow meat!
Step 4: Then use steel pipe to align the chain here, and use steel pipe to align the chain here.
Step 5: Continue to use the bucket to hold the steel pipe to the limit of the rotation force, slowly back feeling stuck to make a click sound, adjust the bucket to continue to hold back.
In the end, the small dig was derailed by prying it with steel pipe and then pinning it with a bucket. Once it fell, it went up. It was as simple as that.







