Quanzhou Sanqi Engineering Machinery Co.Ltd

enLanguage

Slow digging? Teach you to quickly lock the fault point!

Every excavator driver hopes that his work will be vigorous and full of power. In the driving process,  the most depressing thing is that the excavator moves slowly, whether in turn or in operation, like a slow lazy, whenever this time, our excavator master will have a feeling of punching in cotton with no place to make it...            

So, how can we get rid of the problem of slow operation of excavators?            

The slow action of excavator is mainly manifested in three aspects: single action, whole vehicle action and heat action. We will make a concrete analysis of these three issues:            

Slow single action            

The operation of single action is slow, including walking, lifting arm, turning around, turning bucket and so on. If it is a single operation, such as walking, reversing, lifting arms, withdrawing buckets, the speed is relatively slow. It may be due to the following reasons: the overflow valve pressure of excavator related components is too low (need to be tested); pump, low-pressure sensor, multi-way valve failure; related solenoid valve failure, valve core card issuance.           

 One            

Component failure            

That is to say, the action part itself receives bad information or contacts badly in the process of implementation, or the relief valve pressure of the relevant components is too low (relief valve can control the overall pressure, more than the relief valve can withstand the pressure, the hydraulic system will overflow). The operator can see if there are screw loosening or pressure testing by knocking the parts, so as to carry out maintenance and treatment.            

Two            

Conduction process fault            

That is to say, faults occur in the process of command transmission, which hinders the transmission of command signals. Therefore, we can focus on checking the situation of pumps, low-pressure sensors and multiple valves to see if there is a fault.           

 Three            

Operating Center Failure            

That is to say, the command of excavator sends out the central fault, which causes the signal can not be sent. This situation is generally complex and requires professional maintenance guidance. Every excavator can carefully check the relevant solenoid valve fault and whether the valve core is issued card.            The whole car moves slowly.            

One            

Hydraulic system           

Hydraulic system is one of the power systems of excavator. If the excavator is slow, it should check whether the hydraulic system is maintained on time and whether the hydraulic oil is replaced regularly. The expired hydraulic oil will not only affect the performance of excavator, but also corrode the hydraulic wall of excavator. At the same time, we should check whether there is blockage in hydraulic oil circuit and return oil filter element. If there is blockage, we should clean up the oil circuit and replace parts when serious.           

Two            

Engine power is too low            

Like the hydraulic system, the engine is also one of the power systems of excavators. Low power of the engine will lead to low output power, which will cause the excavator to hold up and make the excavator move slowly.            If the output power of the engine is too low and the power is insufficient, please analyze the output of the engine with data, whether all cylinders can work at the same time, check whether there is black smoke in the engine, and if the nozzle is worn seriously, the power of the engine will also decrease.            Three            

Hydraulic pump            

Hydraulic pump output is insufficient, which is one of the transmission failures of the hydraulic system. The operator can enter the service diagnosis system to carry out the related pressure test to see if the excavator is slow because of the transmission of the hydraulic pump.            Insufficient pilot pressure causes insufficient opening spool pressure, resulting in insufficient flow, resulting in slow excavator operation.           

 Four           

 Circuit-related issues            

Excavator CPU, high and low pressure sensor, solenoid valve and line fault.            

Cold machine is normal, heat machine is slow.            

One            

Inspection of oil products            

Check whether the fuel used meets the requirements of excavator, if the fuel has not been replaced for too long and the oil is too dirty, it should be replaced immediately; Check whether the oil filter has copper scraps, causing wear and tear of the main pump, if wear and tear need to be disassembled and checked.            

Two            

Filtrator plugging            

The blockage of the filter element will lead to the oil path is not smooth, so it is necessary to check whether the pilot filter element, the return filter element and the oil absorption filter element are blocked. If the filter element is blocked, it is necessary to clean up the blockage material and replace the filter element when it is serious.            

Three            


Main pump conditioner            

The piston of the main pump conditioner is stained with mud. The excavator works with mud most of the time, so it is inevitable that the piston is stained with mud. But the blockage of the piston will cause the pump pressure of the main pump to decrease, the output power to decrease and the excavator to move slowly. Therefore, in the daily maintenance of excavators, attention should also be paid to cleaning the mud in all parts.

You Might Also Like

Send Inquiry